Results 1 to 4 of 4

Thread: Belt Cover Cracking

  1. #1
    Steve Davis

    Steve Davis, B.Eng., P.Eng., CEng, CPEng, FIMechE, FIEAust

    Principal Advisor

    RioTinto [eDir]

    RioTinto

    Belt Cover Cracking

    Hi all,
    Thought I would see if anyone else has experienced (and has a potential solution for) the issue of very fine cracks appearing in the covers of conventional troughing belts carrying alumina. Alumina can be up to 60 degC max but is usually less than this, around 40 degC. Belts are outside, but covered. Temperature between perhaps 10 and 40 degC ambient.

    The cracks appear fairly soon after installation and don't seem to get worse, maintaining a pace with cover wear.

    Ultra fines appear to get trapped in the cracks and polish the surface of the idler rolls. The fines are released when the belt passes around pulleys and the cracks open creating dust.

    Thanks for any comments.

  2. #2
    Hi Steve

    Cover cracking is typically from excessive heat but can also be caused by UV rays. Even under cover it is not 100% protected.

    Questions that can be asked are:
    1- Was the correct cover compound selected for the application?
    2 - How was the belt stored prior to installation? Storing outdoors and not wrapped can start the process early.
    3 - What are the belt tensions? Higher tensions can speed up the process.

    Good luck in your search for answers.

    All the best
    Gary
    Gary Blenkhorn
    President - Bulk Handling Technology Inc.
    gblenkhorn@bulkht.ca
    http://www.bulkht.ca

    Offering Conveyor Design Services, DEM Flow Simulation Services, Conveyor Transfer Design Services, SolidWorks Design Services for equipment layouts and Software for the Bulk Material Industry.

  3. #3
    Steve Davis

    Steve Davis, B.Eng., P.Eng., CEng, CPEng, FIMechE, FIEAust

    Principal Advisor

    RioTinto [eDir]

    RioTinto

    Cover Cracking

    Hi Gary,
    Thanks for the guidance.

    Temperature is a possible concern for the first belts in this system but it is normally controlled and the alumina would cool by the time it travels the full system.

    UV is a possibility, but the identical length and exposure bauxite belts are fine. My experience of UV cracking is a dry brittle appearance and deeper more widely spread cracks than these, but I agree these could be related.

    Belt cover selection is likely the issue, and I suspect this could be the cause. The original belts were replaced with "equivalent" lower cost belts. As is often the case the history is vague.

    Will keep digging.

    Regards

  4. cover up..

    Hello Steve,

    I got it correctly that the belts in question are these on the alumina side and not those on the bauxite side of the process?
    Now, Al is chemically very reactive, so that the material might alreday influence the surface of the belt. Characteristically, this should then happen only to the carrying side of the belt. If ozone or UV rays are the issue, the effect should be somehow spread further around rthe full belt surface.
    As the cracks (transversal ones only, or also longitudinal cracks?) dont grow in depth, a force or pulley diameter cause seems not so likely.
    Regards
    R.

Similar Threads

  1. Belt Cover Thickness Determination
    By bjsamim in forum Trough Belt Conveying
    Replies: 6
    Last Post: 25th May 2016, 7:59
  2. LRR Cover Belt for Downhill Conveyor
    By Bulk-offline in forum Trough Belt Conveying
    Replies: 7
    Last Post: 20th March 2010, 15:22
  3. Conveyor Belt with Cover 3+0
    By sebastian6002 Singapore in forum New Projects, Tenders, Inquiries
    Replies: 0
    Last Post: 12th April 2007, 4:10
  4. Increasing Heat Resistance of Belt Top Cover
    By rekhawar in forum Trough Belt Conveying
    Replies: 3
    Last Post: 25th February 2005, 23:43
  5. Cover Wear on PVC Belt
    By Shane in forum Trough Belt Conveying
    Replies: 4
    Last Post: 21st October 2004, 3:45

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Single Sign On provided by vBSSO