Results 1 to 5 of 5

Thread: Buckets Handling Steamed Barely

  1. #1

    Buckets handling steamed Barely

    Has anyone a previous experience in proccesing Animal Flaked Barely ?
    My problem in finding the best type of Buckets to be used in the Elevator immediatly after the Flaking Mill. The product is wet Flaked Barely Almost 16% moisture and high temp. steam , almost
    85 Degrees Celcius .
    The original buckets were mild steel last only for few months.
    I am still hesitant to go for plastic or galvanized .

  2. We provide wear resistance solution of many wearing components without failure against severe abrasive attack and abnormal loading condition in raw material handling by fixing laminated plate or bar of Chrome Molybdenum white iron with Chromium 14 to 18%and Molybdenum 2.5 to 3.5 %, metallurgical bonded to a mild steel backing plate. The bond joint is strong metallurgical bond with > 33,000 psi . The chrome Molybdenum white iron wear layer is completely through hardened (i.e. no soft center or back) in the heat treatment process, to a hardness of 700 Brinell, 64 Rockwell C.

    We shall to be pleased discuss further after hearing from you through E.mail.

  3. It seems stainless steel buckets would be the right solution. You have non-abrasive material, but it is hot and steamy (water condensation), so criterion is to have anti-corrosive property.

    Also, your material being non-lumpy, you will not need expensive thick buckets.
    However, check with bucket manufacturers and evaluate their suggestions.

    Regards,
    Ishwar G Mulani.
    Author of Book : Engineering Science and Application Design for Belt Conveyor.
    Email : parimul@pn2.vsnl.net.in
    Tel.: 0091 (0)20 5882916

  4. #4
    gkaraff Guest

    Re: Buckets handling steamed Barely

    Our experience has been with both flaked wheat, corn & milo. We use stainless steel in this type application.

  5. #5
    Paul Haywood Guest

    Plastic buckets

    Dear Mr Uthman

    I can understand your hesitancy regarding plastic elevator buckets, but the correct type will give you excellent service.

    Please let me know the size required (width, projection and depth), the tonnes per hour of the barley handled and the speed of the belt (metres/second) if possible.

    Plastic buckets are not only non-corroding, but would give less sticking of the product in the bucket, and be lighter weight on the belt.

    Best regards
    Paul Haywood
    Muller Beltex UK Ltd
    paul.haywood@mullerbeltex.com
    www.mullerbeltex.com

Similar Threads

  1. Looking for Special Bolts for Buckets
    By prodex in forum Mechanical Conveying
    Replies: 18
    Last Post: 12th May 2015, 7:05
  2. Clamshell Buckets
    By Author in forum New Projects, Tenders, Inquiries
    Replies: 2
    Last Post: 1st July 2007, 4:05
  3. Feeding of Buckets Elevators
    By Osvaldo - Rosario City - Argentina in forum Mechanical Conveying
    Replies: 3
    Last Post: 14th September 2003, 6:30
  4. Manufacturers of Grab Buckets
    By Author in forum New Projects, Tenders, Inquiries
    Replies: 3
    Last Post: 16th April 2003, 22:26
  5. Stainless steel screw conveyors with steamed wall and screw
    By jzamora, Peru in forum Solutions for Screws, Segregation & Solids Flow
    Replies: 4
    Last Post: 5th December 2002, 14:42

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Single Sign On provided by vBSSO