26th November 2011, 16:39
Plaster of Paris Strength Additive
This is jagadeepan, from tamilnadu. I work in a comapny where we produce decorative products out of plaster of paris. Due to the lack of strength of plaster of paris, the products are tend to damage easily. Can you please tell me, any additives like chemicals that can be blended with plaster of paris for strength. I find you have very good knowledge about cements. So i decided to write this to you.
9th December 2011, 3:40
Consider mechanical reinforcement such as chopped fiberglass fibres.
11th December 2011, 14:29
Please note that in India 80% of plaster of Paris from Local Producers is not up to the mark.The main producing State is Rajasthan where, producers do not calcine the raw material properly and also the raw material is not good. So first look at the quality of your POP.
For reinforcing some producers even use cuttings from USED PP bags of cement.
11th December 2011, 19:58
Concrete class upgrading liquid admixture
CONCRETE CLASS UPGRADING LIQUID ADMIXTURE
Originally Posted by anil_ seth
Admixture K100® or as we say “K100”, is a liquid form of KALMATRON® KFA, worldwide known as a Concrete Class Upgrading Admixture.
K100 acts by four ways after pouring into the concrete batch:
1.As a Water Reducer during of mixing and pumping time;
2.As a Plasticizer during of transportation and placement time;
3.As a Shrinkage controlling and Curing Compound during of setting time;
4.As a Strength gainer and impermeability performing agent of hardening time.
K100 is dosed by 54 OZ/CY (2 Liters/m3) or 10 OZ per 100 LB (0.7 Liter per 100 Kg) of cement for any field of the concrete and mortars applications.
Product dispensed into the plastic buckets by 4.8 GL (17.7 Liters) or into the IBC by 264 Gallons (1000 Liters) each. Highly economical even by small purchased volumes.
K100 is approved and registered by the USA International Sanitary Fund by #143075, Code R2, RX2 and patented in the USA #3,680,881 and EU #6915839.
Mr. Dilip Shah
N R D Industries
14 Whittlesey Avenue
West Orange, NJ 07052.
E-mail : firstname.lastname@example.org, email@example.com
E-mail : firstname.lastname@example.org, email@example.com, firstname.lastname@example.org
Phone/Fax : 650-872-2555
11th December 2011, 20:03
11th December 2011, 20:11
Concrete class upgrading liquid admixture
19th December 2011, 23:27
Originally Posted by Author
We appreciate that you took time from your busy day to take attention to this message, please view this mail in .Please allow us to introduce ourselves, we are N R D Industries. We are the distributor of KALMATRON®, a SUPER CONCRETE ADDITIVE that we believe has no equal in the United States or world-wide. Below is a brief description of products, and also enclosed is more literature for the same.
Kalmatron® Corporation has been established by the owners of patents, technologies, and trademark of Kalmatron® products. Kalmatron® Corporation is the manufacturer and supplier of its products for the building industry on the world market by appointed agencies and companies.
The Kalmatron® concept was discovered by Dr. Alex V. Rusinoff in 1982. First production began in 1992. The Kalmatron® theory created different mechanisms of cement grain decay, which gives numerous technologies for repair and building of new structures with highest performance of durability.
Products Trade Name Description
Admixtures & Coatings
Admixture KF-A KALMATRON® KF-A
KALMATRON® KF-A is the first of the generation of chemically active admixtures to the cement containing mixes that increases cementiiotus value and volume of cement grain. Therefore, the lower quality cement has the higher the effectiveness of KF-A. That is why the results of applications are varying but always exceeding targeted one.
Coating KF-B KALMATRON® KF-B
KALMATRON® KF-B works as a remedial coating on old, aged, or deteriorated concrete and masonry structures in a damp environments.
KALMATRON® KF-B is the only known product that works in severe sewage, acid, and petroleum rich environments as a continuous coating. Preparation on the job site only involves mixing KF-B powder with water in a volume to volume ratio of 3 to 1.
Hardened Plugs KF-C KALMATRON® KF-C
KALMATRON® KF-C is the fastest hardening plug compound for stopping pressured leaks in concrete, wooden, and masonry structures. KF-C plugs leaks with pressures up to 19 Bar. It is applicable in underwater conditions with the use of hardened KF-C plugs or a compressor for pressure strewing KF-C powder.
Admixture KF-D KALMATRON® KF-D
Light gray powder with specific smell. After application, the smell disappears. This inorganic compound works as an admixture to cement containing Earth-Materials-Sealants (EMS).
Improves density and impermeability of soil or severely deteriorated structures. KF-D added to standard EMS mixes can be used for injections under or into sinkholes, foundations, tunnels, dams, wet and polluted soils, etc.
Coating KF-ECOAT KALMATRON® KF-ECOAT
ADVANTAGES OF COATING KF-ECOAT
Simplest surface preparation---just wet the surface with water.
Applicable under low temperature on site.
No specific qualification of staff is required.
No costly removal and replacement of the deteriorated structure-just restore it.
Impermeability to wall seepage is 100%.
Hardner - KF-EHARD KALMATRON® KF-EHARD
ADVANTAGES OF HARDENER KF-EHARD
Non-Rusting - Stain-Resistant
Permanent color - non-fading
Curing effect of fresh concrete surface is provided.
Various types of finishes and coloring effects
Increases serviceability of concrete floors.
Admixture KF-EADMIX KALMATRON® KF-EADMIX
ADVANTAGES OF ADMIXTURE KF-EADMIX
The water-cement ratio is standard or lower by up to 10%.
The mixing time is standard and the viscosity of the mix is much better.
Slump is higher by up to 20% without additional water.
Shrinkage is lower by up to 35%.
Impermeability of structure is 100%.
Protective Coating -KF-F KALMATRON® KF-F
KALMATRON® KF-F is the strongest protective coating for old and/ or deteriorated concrete and masonry structures. Provides superficial density with highest resistance to chemical and environmental corrosions. KF-F is liquid-impermeable and is the best available coating against abrasion, vapor and liquid transmission, and freeze-thaw cycles. Applicable in dry, hot, cold and damp environments by brush or spray.
Light-gray to ivory colored coarse powder; after being mixed with water, it becomes a light yellow solid.
Liquid Spray KF-G KALMATRON® KF-G
KALMATRON® KF-G is a liquid spray for rehabilitation of degraded concrete rheology. KF-G represents a new concept in concrete rehabilitation technology and became highly popular because of its effective performance and simplicity of application. In most cases, after KF-G is applied to the damaged area there is no need for it to be covered with any additional layer.
Cementitious Coating KF-H KALMATRON® KF-H
KALMATRON® KF-H is a finishing cementitious paint and patching material for protection of wooden structures. The 1.5 mm thick layer of KF-H provides a durable coat with highest resistance to atmospheric and biological damage. KF-H is applicable by brush or trowel in dry and damp environments. Provides rock solid abrasion resistance, liquid impermeability, and freeze-thaw resistance. KF-H waterproofs both the negative and positive sides of dry orsoaked surfaces.
Heat/Cold Isolation Compound KF- I KALMATRON® KF- I
KALMATRON® KF-I is a thermoresistant inorganic, non asbestos compound designed for heat/cold protection of concrete, masonry, and wooden structures. KF-I is impermeable to liquids and attenuates temperature cycles.
KALMATRON® KF-I is applicable for industrial walls and ceilings of metallurgic and chemical industries, food processing and storage facilities, cooling tanks of nuclear plants, fire protection separators, boiled water supply pipes, heating joints, etc.
PreMix KF-JET KALMATRON® KF-JET
KALMATRON® KF-Jet designed as a premix to the dry Ordinary Portland Cement (OPC) powder for production of Rapid Set Cement (RSC) and Fast Setting Cement (FSC) with controlled setting time.
Distinctive difference from known products is that concrete after application has twice lower drying shrinkage cracks, higher compressive strength and adjustable hardening time.
Admixture KF-K KALMATRON® KF-K
KALMATRON® KF-K is an admixture to conventional concrete mixes used to quickly prepare Patching Concrete with high viscosity, strong adhesion and without cracks. KALMATRON® KF-K, added as 10 Lbs/CY or 6 Kg/m3 increases resistance to abrasion and impermeability to any liquids, including purified oil and gasoline. Final Hardening Time (FHT) varies from 45 minutes to 4 hours, which depends on patch size, water amount and/or mixer speed.
Admixture KC KALMATRON® KC
KALMATRON® KC was developed as an admixture to cement to increase hydration by molecular decay of unstable relations between foreign inclusions with cement particles. After that, hydration is an entirely completed reaction with higher performance of concrete rheology that obtained many features of High Performance Cements and High Alumina Cements. The lower the grades of cement powder, the higher the effectiveness of KC.
Admixture KF-SEA KALMATRON® KF-SEA
KALMATRON® KF-SEA is an admixture to regular concrete mixes containing unwashed sea sand and sea gravel where hydration of cement may be provided with sea water as well. Gray powder with specific smell. After application the smell disappears. This inorganic cementitious compound discharges the electrochemical potential of most sea salts, which are aggressive to concrete structures.
Used for enhancing concrete and reinforced concrete in centrally loaded foundations, pillars, walls, columns, etc. Not for bending elements with thickness less than 450 mm. Used for Facilities for Industrial and Military hazardous waste, dams, tunnels, heavy traffic roads, ramps, seaports, airports, etc.
Cementitious Radiation Attenuation KF-αβγ KALMATRON® KF-αβγ
KALMATRON® KF-αβγ is a cementitious powder designed for attenuation of α, β and γ radiation. KF-αβγ dry density is 2,500 Kg/m3, wet density is 3,500 Kg/m3. KF-αβγ deactivates contamination, restores building structures, attenuates radiation and supresses sources of radiation and other radioactive contamination. KF-αβγ can be applied as a coating, as an admixture to the concrete mix, or it can be strewn onto or into the source of radiation.
Additive KF-ASH KALMATRON® KF-ASH
KALMATRON® KF-ASH is an additive to concrete mix containing over 50% of fly ash, slag ash or crumbled slag from the weight of cement. In order to utilize incinerated industrial waste (IIW) with maximum benefits, that concrete can be successfully used for conventional structures and is widely recommended for urban infrastructure.
Concrete Masonry Unit (CMU) KALMATRON® BLOCK
Concrete Masonry Units are available in standard demensions with different shapes and volumes of air-enclosed space for use in diverse climates.
Earthquake Protection SEISMIC STAR
Seismic Star is an underground wall designed for dissipation of shear rupture between soil and Seismic Star with reduction of impulse surplus pressure up to 40% and more.
Admixture К100® Admixture К100®
К100® is a concrete class upgrading admixture applicable where concrete, grout, or plaster need to be without shrinkage cracks, efflorescence, and post-hardening deformations, water/vapor proof, and stable to ecological and industrial corrosions (рН<3; salt up to 20%; temperature up to +400°С and - 50°С).
Unique Applications of KALMATRON®
KALMATRON® products are widely distributed on the world building materials market for the conventional applications and unique projects.
SHIELDCRETE The companies "Kalmatron® Corporation", and "Shotcrete Technologies Inc." provide unique shotcrete technologies and materials for cliquid impermeability, superficial density and compressive strength.
KALMATRON® PLASTCRETE Highest performance of successfully designed and applied PLASTCRETE classifies it as a protective remedial layer with effectiveness of sophisticated coats and simplicity of stucco application.
It's all about polymers which are never been known for durability and accepted by Int. sanitary foundation. It is a past of civilization.
Thousands of domes are built in the USA made of shotcrete with KF-A by our mix design Plastcrete as attached to this letter (www.shieldcrete.com).
Thousands miles of water carrying pipe lines and aqueducts are repaired by Kalmatron, which saved trillions of dollars to replace them.
We ensure you to provide the best services and technical back-up to your applications. Please contact us at email@example.com for more information regarding the information mentioned above or enclosed within. Thanking you in advance for your time and hoping to hear from you soon.
Mr. Dilip Shah
N R D Industries
14 Whittlesey Avenue
West Orange. NJ 07052.
Cell No: 1-848-391-1248
E-mail : firstname.lastname@example.org, email@example.com, KalmatronWorld@aol.com
Dr. Alex Rusinoff Tel No: 1 415 385 3290
12th September 2012, 18:47
Wide range ofAdmixtures forNew Buildings, Coatings,Spray for Restoration of Aged Ones
Please allow us to introduce ourselves, we are KALMATRON®, a SUPER CONCRETE ADDITIVE that we believe has no equal in the United States or world-wide. N R D INDUSTRIES. is the exclusive distributor of the concrete admixtures created by the KALMATRON® Company a non-exclusive distributor of the product.
We work with our clients to find the best solution for all proposed contracts. Our product line consists of over 15 differing solutions of our product, each designed for specific applications.
We will look into your unique concerns and diagnose the best solution to rectify the problem, or in the case of protecting new concrete, we will help suggest which product will help increase the lifespan and lifetime durability of the structure.
We conduct these evaluations free of charge because we are in the business of protecting concrete and believe it important to do the job right, the first time around. Unlike many of the other admixtures on the market, Kalmatron® is not easily classified as a 'retarder,' 'superplasticizer,' 'accelerator,' 'water reducer',' or 'air entrainer' because our product upgrades concrete in a completely new and revolutionized way. To understand how we differ from the competition, it is important to know about the history of our supplier.
When mixed or applied onto concrete, these Kalmatron® solutions offer a host of improvements to the compound, including but not limited to:
• Increasing compression strength
• Protection against rebar corrosion and rust
• Protection from the seepage of engine and diesel oil
• Reducing the effects of carbonization
• Reducing penetration of chloride salts
For a description of the products we offer please visit our Products page and for examples of the projects we have completed and the testimonials we have received visit our Projects section.
We have admix KF-A or K100 its liquid version added to plaster or concrete provides completed oil impermeability See www.shieldcrete.com where penetrating of crude oil through the concrete wall of aqueduct was stopped by 3/4" or 18 mm thick layer.
Actually, we can supply ready to apply plaster or concrete for this type of projects but better to sell them admixtures.
Below is a brief description of products, and also enclosed is more literature for the same.
KALMATRON SHOT ROBOT.FLV
CONCRETE FLOOR ABRASION vs KALMATRON K100, W:C 42
KALMATRON® KF-B is a powder after mixing with water works as a coating on old, aged, or deteriorated concrete and masonry structures in a damp environments.
By definition, KALMATRON® KF-B is a protective composition that penetrates into the structure.
Provides ion-kation exchange that recuperates anhydrate cement grains from being as a sponge to the particle with low sorption ability or with repellence to any grade of moist.
Improves density, compressive strength, abrasion and chemical resistance, gas and liquid impermeability, and freeze-thaw resistance. Works from both negative and positive waterproofing sides. Applicable by metal trowel, brush, and spray providing machinery.
Please contact us at firstname.lastname@example.org for more information regarding the information mentioned above.
Mr. Dilip Shah
N R D Industries
14 Whittlesey Avenue
West Orange. NJ 07052.
By marikaya in forum Ask Lyn Forum
Last Post: 25th July 2007, 10:59
By srconsul in forum Weighing, Dosing & Proportioning
Last Post: 8th July 2006, 10:02
By Dave Meyers in forum Mechanical Conveying
Last Post: 16th October 2004, 23:38
By M. Liesenhoff in forum New Projects, Tenders, Inquiries
Last Post: 2nd June 2003, 13:45
By prodex in forum Representatives & Distributors
Last Post: 19th April 2002, 23:28
Tags for this Thread
Single Sign On provided by vBSSO